MATT 2:1

Matt acrylic clear coat

Variantes

ColourArt. No.CapacityQuantity per carton
transparent63011 l6
Hardener
matt 1:263000,5 l6

Grado de brillo

matt
MATT 2:1

Documentación técnica

Video

Description

High-quality matt acrylic clearcoat with a special effect. Intended for specialized repairs of car body parts that require a matt finish. It allows to obtain an evenly matt surface as well as a strong and durable finish.
Matt 2:1 Clear Coat can be mixed with Inter Troton Crystal and Zircon clear coats, as well as with Multi Füller MS 2:1.
Different degrees of matt are obtained depending on mixture ratios.

Degrees of the matting effect:

matt

Advantages

  • Perfect matt finish.
  • Very good flow and levelling.
  • Durable coating.
  • Increased resistance to scratches SR (Scratch Resistant).

Substrates

MATT 2:1 2K acrylic clear coat can be applied over:

  • Base coats.
  • Old coatings in good condition after sanding and degreasing.

Información importante sobre el uso del producto

  • Przetrzeć odtłuścić

    degrease

  • Proporcje mieszania

    Mixing proportion
    2 : 1 + 10%

  • Lepkość natryskowa

    Spraying viscosity
    16 ÷ 18s / 20°C

  • Żywotność mieszanki

    Pot life for the mixture
    ~ 7h /20°C

  • Liczba warstw

    2 layers
    HVLP / RP
    ø1,3 ÷ 1,4 mm

  • Czas odparowania

    between layers
    10 ÷ 15 min.

  • Czas utwardzania

    Drying time
    24 h / 20°C

  • Zamieszać

    Caution: Stir well before using.

Proceso de aplicación

  • Zastosowanie
  • Use

    Fast car body repairs that required matt durable finish.

  • Proporcje mieszania
  • Mixing proportions per volume

    Clear coat: 2
    Hardener: 1
    Thinner: 10%

  • Lepkość natryskowa
  • Spraying viscosity

    16÷18 seconds at 20ºC

  • Żywotność mieszanki
  • Pot life for the mixture

    About 7 hours at 20ºC

  • Liczba warstw
  • Number of layers

    Number of layers
    2 layers evenly applied;
    about 50-60 µm of dry coating.
    RP gun parameters
    Nozzle: 1,3÷1,4mm; Pressure: 2,0÷2,2 bar.
    HVLP gun parameters
    Nozzle: 1,3÷1,4mm; Inlet pressure: 2,0 bar.
    Caution: Follow the recommendations of the equipment manufacturer

  • Czas odparowania
  • Flash off time

    Between layers:
    about 10÷15min.

  • Czas utwardzania
  • Hardening time

    Dust dry:
    30 minutes at 20ºC
    Touch dry: 24 hours at 20ºC

    Temperatures below 20°C significantly increase the drying time.

  • Informacja
  • Performance

    1 liter of the mixture is enough to paint 8÷9 m2 of surface with a layer thickness of 50 μm.

  • Informacja
  • Polishing and eliminating defects

    Caution: Do not polish matt coatings!

  • Informacja
  • General notes
    • Do not exceed recommended doses of the hardener!
    • The best repair results can be achieved by painting at room temperature. The temperature in the body shop and the temperature of the product should be similar. When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and airways.
    • The rooms should be well ventilated.
    • Clean the guns and equipment immediately after use.

    Caution: To maintain safety, always follow the instructions given in the MSDS for the products.

Haga una pregunta sobre el producto



       
    Ver también otros productos
    Wyjście 
    Go to top